#Yaesu u ftdx3000d mil3 reviews upgrade
#Yaesu u ftdx3000d mil3 reviews software
#Yaesu u ftdx3000d mil3 reviews plus

If youвЂ™re looking at a RTTY signal being demodulated, the knob that serves to set the RX clarifier or memory channel is taken over (again), and you canвЂ™t change either setting. Although to be fair, if you hold down some of the controls for a few seconds, it does take you right to the relevant menu item. When youвЂ™re using it (for instance, to adjust drive to a linear), the VFO B knob can only be used to adjust power, which in turn means you canвЂ™t adjust the TX clarifier, which in turn means you canвЂ™t politely hop a little off frequency unless you carefully do that before you open the menu to adjust power.ДЄlso, you can customize exactly one button to take you to the menu item of your choice, so choose wisely, grasshopper. ThereвЂ™s no readily available SSB RF output level control until you go menu mining. Next, there are some really odd UI issues. But I canвЂ™t believe that anyone who has even a hint of what a spectrum should look like would be anything but bitterly disapointed with this tiny, slow and inaccurate attempt at an old-school panadaptor.

#Yaesu u ftdx3000d mil3 reviews plus

In my situation, since an SDR plus SdrDx gives me fine-grained, high speed, and very accurate spectrum and waterfall displays for both RF and audio, I really donвЂ™t use the radioвЂ™s spectrum display and always leave the 8 buttons up that cover it. With future radio designs, Yaesu should copy KenwoodвЂ™s process. I suppose I should be grateful the radio works well enough to not need the upgrade.

#Yaesu u ftdx3000d mil3 reviews software

After experiencing the beautifully clean process the Kenwood TS-990S uses, it became clear to me just how backwards and arcane the Yaesu process actually is - not only would I have to obtain a Windows PC, there is auxiliary software to install, four different possible upgrades you have to choose from manually, cable selections to make, four different downloadsвЂ¦ itвЂ™s as if they were trying to make it as difficult as possible.

#Yaesu u ftdx3000d mil3 reviews upgrade

In the ham bands, itвЂ™ll lock down and is much easier to see, although since what is on it is mostly nonsenseвЂ¦ well, you get the idea.Д®DIT 20140216: There is a firmware upgrade for the FTdx3000, but upon examining the process by reading the FTdx3000 upgrade manual, I abandoned any intent of installing it. ThereвЂ™s no waterfall for RF (though there is for audioвЂ¦ curious.) Outside of the ham bands, thereвЂ™s no fixed capability, only tuning/tracking so the spectrum is always sliding around as you tune, no choice. ItвЂ™s way, way too slow вЂ“ updates are jerky and thereвЂ™s zero sense of modulation matching the display. What little it does show, it shows incorrectly вЂ“ just little вЂњlumpsвЂќ that do not even come close to representing the spectral activity actually going on. I canвЂ™t recommend the radio very highly for вЂњnormalвЂќ use there are simply too many problems for a radio in this price range if you use it as you are expected to.ДЇirst of all, the spectrum display: It is terrible. I did my research, I got what I asked for, and I am happy as a clam. I get a far superior receive capability to any traditional radio on the market at any price including the very best from Yaesu, Kenwood and ICOM, *plus* the radioвЂ™s own capabilities as a medium quality second receiver in-band if I want that. This works as planned, and so I am well satisfied with the radio in my installation. I added the FTDX 3000 to my station in order to use it differently than most users will my setup uses the transmit portion of the radio as usual, but utilizes the IF output on the rear deck to replace most of the receive capability with an SDR on the IF, and my SdrDx software working with the SDR.